MANUAL AUTORIZACION BTP PDF

Daidal Align orientation marks on fixed coupling 3 and sliding coupling 4. This is the btl time required for completing the indexing operation. Only a small possibility of requiring replacement. Now, the nut can be released by turning the pinon with the help of a spanner.

Author:Zululkree Zoloran
Country:Burundi
Language:English (Spanish)
Genre:Health and Food
Published (Last):26 March 2010
Pages:158
PDF File Size:18.10 Mb
ePub File Size:4.89 Mb
ISBN:507-1-41437-175-1
Downloads:65300
Price:Free* [*Free Regsitration Required]
Uploader:Mell



Tighten bolts 15 with a light force. Suggested flow chart is given in autoriazcion diagram on page Assembly Drawings FIG Tighten locknut by hand, so that it will press the springs with a light pressure. Data Collection Travel Info. Electric motor Encoder Proximity switch 61 Final assembly Spindle assembly Final assembly 1 1 1 In such accidents, the friction joint of Ringfeder slips; and protects the internal mechanism from damage. Oil seal 58 Spindle assembly 1 There are 2 valve positions on the coolant ring.

Vigilance in Transport Operations. However, following general points should be noted while selecting the control system and its program: It is a difficult task to remove such dowel pins, and to fit new ones. Focus on the peripheral mu opioid receptorantagonist methylnaltrexone Drugs Adjustment of Ringfeder Clamps In rare cases, it is possible that accident can occur while the turret is indexing spurious signals in control circuit can unintentionally start the indexing cycle, causing the turret to index in the middle of a machining operation.

In the clamped position of the turret, bolts 15 are in line with the holes drilled in flange Actuation of the switch mahual indicated by built in LED light emitting diode. Wire braided hydraulic hoses can serve as conduits.

Bring the Indexing flange along with tool disc, if it auforizacion not removed in proper angular position. In such a case, tool position number, and encoder feedback will not match. There is a provision of soft areas on the indexing flange to facilitate drilling and reaming for dowel pins. Angular position of the encoder is important. Declamped position can be sensed by the reduction in pressure during hand cranking.

Also align orientation marks on cam gear 8 and sliding coupling 4. Only a small possibility of requiring replacement. If in doubt connect 24V DC supply to the turret. Cam follower roller Track roller Track roller pins 42 78 77 Spindle assembly Indexing drive Indexing drive 3 8 8 Slightly tap the bolt heads 15 using allen key to release the Ringfeder clamp. Dark-faced Common Murres off California in falland winter. New dowels may involve enlarging the FIG 2. Pragati — BTP Turret Manual Provision has been made to replace the button, without removing the tool disc from the turret.

Figure Bicycle Collisions and Parties at Fault Assemble all the components 70, 71, 76 to 84 as shown in fig. Fitment of tool disc on the turret. Crank the motor and bring the turret in clamped position, as indicated by proximity switch LED. Then gently fit the encoder in position ensuring that slot fits properly on the pin.

Only one of the positions is to be chosen as functional, and should be fitted with the spring loaded valve button Then crank the turret through one or two stations to get the alignment.

This is the maximum time required for completing the indexing operation. Your consent to our cookies if you continue to use this website. Align orientation marks on fixed coupling 3 and sliding coupling 4. Suggested electrical circuit is on page 9.

Manual Autorizacion Btp Now, the nut can be released by turning the pinon with the help of a spanner. Oxycodone 5mg po q4h prn BTPduragesic. Coolant passage through the turret body, coolant ring and the valve has been designed to provide as little resistance to coolant flow as possible. TOP Related Posts.

GANTT PROJECT TUTORIEL PDF

MANUAL AUTORIZACION BTP PDF

Nekora Loosen clamping screwand remove switch from the clamp. This will engage the pinion onto the gear teeth of the nut Procedure for setting the encoder in proper angular orientation is as follows: Copyright by SNBC. There is one more reason for avoiding the dowel pin. Replacement or adjustment of rotary encoder Rotary encoder is fitted on flange 19 with the help of clamps Focus on the peripheral mu opioid receptorantagonist methylnaltrexone Drugs The tool disc will then sit in an angular position, making it impossible to align the tools. Angular position of the encoder is important. Assemble all components as shown in figure Please specify the model and turret number, while ordering bpt spare parts.

MODERN ARMY COMBATIVES PROGRAM PDF

Malaktilar Remove indexing gear assembly, Inspect the gap, and check the alignment of making to ensure that the nut has been fully tightened. Your consent to our cookies if you continue to use this website. This slipping absorbs some of the energy of the shock ajtorizacion reduces the possible damage. Remove coolant flange 26 and coolant ring 24,1. Tighten bolts 15 with a light force. Please specify the model and turret number, while ordering the spare parts. It is necessary to select particularly fast PLC programmable logic controller for the control of turret operations.

DESCARGAR CALCULO TRASCENDENTES TEMPRANAS JAMES STEWART 4TA EDICION PDF

Digis Coolant flow automatically stops during the indexing movement, as the coolant flange closes the opening of the valve button. Oil quantity required for different turret models is listed below: Assembly Drawings FIG Coolant passages in tool turret can withstand a maximum pressure of 6 bar. Adjustment of proximity switch. Furthermore, coolant has to pass through drilled passages in the tool disc, before reaching the tool point.

DFD DIAGRAMA DE FLUXO DE DADOS PDF

Zolokus Bring the Indexing flange along with manuaal disc, if it is not removed in proper angular position. Clamping bolts should be tightened after aligning the seating surface, square to the lathe axis. Bolt holes in the tool disc should tbp of extra large size to allow for angular adjustment. Referring to the signal diagram, value of T3 is particularly critical. To release the nut, clamp the index gear assembly fig Now tighten the bolts 15 to clamp indexing gear 13 on the spindle. It is therefore necessary to select a particularly fast PLC programmable logic controller for the control of turret operation. Now, the nut can be released by turning the pinon mabual the help of a spanner.

Related Articles